as电玩

Product features

• ▪ Radiation immunity test: meet the requirements of iec/en 61000-4-3 and other standards;
  
• ▪ Shielding efficiency: meet the standard en50147-1;
  
• ▪ Radiation emission test: meet the requirements of EN 50022, en 50147-2, GJB 151a, GJB 152A and other standards

Product parameters

• Internal dimension
  

  
  

  Space requirements
  

  
  

  Free space
  

  
  

  -
  

  
  

  frequency
  

  
  

  
  

  
  

  
  

  
  

  
  

  
  

  
  

  performance
  

  
  

  
  

  
  

  
  

  
  

  
  

  
  

  
  

  
  

  Field source
  

  
  

  
  

  
  

  
  

  
  

  
  

• About: 9.1 x 5.8 x 5.55 meters (length x width x height)
  

  About: 11.0 x 7.8 x 7.0 meters (length x width x height), depending on the type of support
  

  About: 8.4 x 5.1 x 5.1 meters (length x width x height)
  

  EN 50147-1 and mil STD 285
  

  10 kHz
  

  100 kHz
  

  1 MHz
  

  10 MHz
  

  100 MHz
  

  1 GHz
  

  2GHz
  

  -
  

  70 dB
  

  80 dB
  

  100 dB
  

  100 dB
  

  100 dB
  

  100 dB
  

  100 dB
  

  -
  

  H
  

  H
  

  H
  

  E
  

  E
  

  PW
  

  Pw

Product recommendation

Power frequency magnetic field generator PFM 1200

Model：PFM 1200

The power frequency magnetic field is generated by the power frequency current in the conductor, or a very small amount of it is generated by other accessories (such as the leakage flux of the transformer). Power frequency magnetic field may affect the reliable operation of equipment and system. The power frequency magnetic field generator is used to evalsuate the performance of household, commercial and industrial electrical and electronic equipment in power frequency (continuous and short-time) magnetic field. The products meet the requirements of new standards such as iec61000-4-8 and gb/t17626.8.

Learn more

Single Phase 10A Voltage Dips Generator

Model：VDT S10

Voltage dips/sags, short interruptions are caused by failures of the power grid and power facilities or sudden large changes in loads. In some cases, there will be two or more consecutive dips or interruptions. Voltage changes are caused by continuous changes in the loads connected to the grid. If the EUT cannot respond in time to changes in the power supply voltage, it may cause malfunctions. Voltage dips generators are used to evalsuate the performance of electrical and electronic equipment when subjected to voltage dips/sags, short interruptions, and voltage changes. Products fully meet the requirements of standards IEC/EN 61000-4-11 and GB/T17626.11.

Learn more

Three phase 6kV pulse group generator EFT T6

Model：EFT T6

In the circuit, such as from the switching transient process (cutting off inductive loads, bouncing relay contacts, etc.), it will usually interfere with other electrical and electronic equipment in the same circuit. This kind of interference is characterized by high amplitude, short rise time, high repetition rate and low energy. Clusters of narrow pulses can charge the junction capacitance of semiconductor devices, which may cause circuit or equipment errors when accumulated to a certain extent. The burst generator determines a common reproducible evalsuation basis for evalsuating the performance of power supply ports, signal, control and grounding ports of electrical and electronic equipment when disturbed by electrical fast transient bursts. The products meet the requirements of new standards such as iec61000-4-4, en60100-4-4 and gb/t17626.4.

Learn more